MAX232
The MAX232 is an integrated circuit by Maxim Integrated Products, now a subsidiary of Analog Devices, that converts signals from a TIA-232 (RS-232) serial port to signals suitable for use in TTL-compatible digital logic circuits. The MAX232 is a dual transmitter / dual receiver that typically is used to convert the RX, TX, CTS, RTS signals.[1]
The drivers provide TIA-232 voltage level outputs (about ±7.5 volts) from a single 5-volt supply by on-chip charge pumps and external capacitors. This makes it useful for implementing TIA-232 in devices that otherwise do not need any other voltages. The receivers translates the TIA-232 input voltages (up to ±25 volts, though MAX232 supports up to ±30 volts) down to standard 5 volt TTL levels.[1] These receivers have a typical threshold of 1.3 volts and a typical hysteresis of 0.5 volts.[1]
The MAX232 replaced an older pair of chips MC1488 and MC1489 that performed similar RS-232 translation. The MC1488 quad transmitter chip required 12 volt and −12 volt power,[2] and MC1489 quad receiver chip required 5 volt power.[3] The main disadvantages of this older solution was the ±12 volt power requirement, only supported 5 volt digital logic, and two chips instead of one.
History
The MAX232 was proposed by Charlie Allen and designed by Dave Bingham.[4][5][6] Maxim Integrated Products announced the MAX232 no later than 1986.[1]
Versions
The later MAX232A is backward compatible with the original MAX232 but may operate at higher baud rates and can use smaller external capacitors – 0.1 μF in place of the 1.0 μF capacitors used with the original device.[7] The newer MAX3232 and MAX3232E are also backwards compatible, but operates at a broader voltage range, from 3 to 5.5 V.[8][9]
Pin-to-pin compatible versions from other manufacturers are ICL232, SP232, ST232, ADM232 and HIN232. Texas Instruments makes compatible chips, using MAX232 as the part number.
Voltage levels
The MAX232 translates a TTL logic 0 input to between +3 and +15 V, and changes TTL logic 1 input to between −3 and −15 V, and vice versa for converting from TIA-232 to TTL. (The TIA-232 uses opposite voltages for data and control lines, see RS-232 voltage levels.)
TIA-232 line type and logic level | TIA-232 voltage | TTL voltage to/from MAX232 |
---|---|---|
Data transmission (Rx/Tx) logic 0 | +3 V to +15 V | 0 V |
Data transmission (Rx/Tx) logic 1 | −3 V to −15 V | 5 V |
Control signals (RTS/CTS/DTR/DSR) logic 0 | −3 V to −15 V | 5 V |
Control signals (RTS/CTS/DTR/DSR) logic 1 | +3 V to +15 V | 0 V |
Applications
The MAX232(A) has two receivers that convert from RS-232 to TTL voltage levels, and two drivers that convert from TTL logic to RS-232 voltage levels. As a result, only two out of all RS-232 signals can be converted in each direction. Typically, the first driver/receiver pair of the MAX232 is used for TX and RX signals, and the second one for CTS and RTS signals.
There are not enough drivers/receivers in the MAX232 to also connect the DTR, DSR, and DCD signals. Usually, these signals can be omitted when, for example, communicating with a PC's serial interface, or when special cables render them unnecessary. If the DTE requires these signals, a second MAX232 or some other IC from the MAX232 family can be used.
Derivatives
The MAX232 family was subsequently extended by Maxim to versions with four transmitters (the MAX234) and a version with four receivers and four transmitters (the MAX248), as well as several other combinations of receivers and transmitters. A notable addition is the MAX316x which is able to be electrically reconfigured between differential 5 V (RS-422 and RS-485) and single-ended RS-232 albeit at reduced voltage.
References
- ^ a b c d "At Last, It's Easy To Design RS-232-C Modems" (PDF). Electronics: 89–92. 1986-07-24.
- ^ MC1488 (MC1488, SN55188, SN75188) product webpage; Texas Instruments.
- ^ MC1489 (MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A) product webpage; Texas Instruments.
- ^ EDN Staff, ed. (1997-05-08). "EDN's 1996 Innovator / Innovation Competition". EDN. Archived from the original on 2021-12-10. Retrieved 2021-12-10.
- ^ Sherman, Len (2016-12-16). "Almost 30 years of the MAX232". BISinfotech. Archived from the original on 2021-12-10. Retrieved 2021-12-10.
The MAX232's success was as much a tribute to the vision of its definer, Charlie Allen, as it was to the ingenuity of its designer, Dave Bingham.
- ^ Fox, Brett J. (2021). "What Makes Your Great Engineers Great?". Archived from the original on 2021-12-10. Retrieved 2021-12-10.
The launch of the MAX232 family is particularly insightful. Charlie Allen, a brilliant, customer focused, applications engineer, noticed that our customers were using a product called the ICL7660, which Dave [Bingham] also designed, to provide the negative power supply for RS-232 line drivers and receivers. So, Charlie approached Dave, and asked Dave if he could design an IC that integrated the functionality of the ICL7660 with an RS-232 line driver and receiver.
- ^ MAX232 (MAX220 to MAX249) product webpage; Maxim.
- ^ MAX3232 (MAX3222 to MAX3241) product webpage; Maxim.
- ^ MAX3232E (MAX3222E to MAX3246E) product webpage; Maxim.