A blended wing body (BWB), also known as blended body, hybrid wing body (HWB) or a lifting aerofoil fuselage,^[1] is a fixed-wing aircraft having no clear dividing line between the wings and the main body of the craft.^[2] The aircraft has distinct wing and body structures, which are smoothly blended together with no clear dividing line.^[3] This contrasts with a flying wing, which has no distinct fuselage, and a lifting body, which has no distinct wings. A BWB design may or may not be tailless.

The main advantage of the BWB is to reduce wetted area and the accompanying form drag associated with a conventional wing-body junction. It may also be given a wide airfoil-shaped body, allowing the entire craft to generate lift and thus reducing the size and drag of the wings.

The BWB configuration is used for both aircraft and underwater gliders.

In the early 1920s Nicolas Woyevodsky developed a theory of the BWB and, following wind tunnel tests, the Westland Dreadnought was built. It stalled on its first flight in 1924, severely injuring the pilot, and the project was cancelled. The idea was proposed again in the early 1940s for a Miles M.26 airliner project and the Miles M.30 "X Minor" research prototype was built to investigate it. The McDonnell XP-67 prototype interceptor also flew in 1944 but did not meet expectations. The 1944 Burnelli CBY-3 Loadmaster was a blended wing design intended for Canadian bush operations.^[4]

NASA and McDonnell Douglas returned to the concept in the 1990s with an artificially stabilized 17-foot (5.2 m) model (6% scale) called BWB-17, built by Stanford University, which was flown in 1997 and showed good handling qualities.^[5]: 16 From 2000 NASA went on to develop a remotely controlled research model with a 21-foot (6.4 m) wingspan.

NASA has also jointly explored BWB designs for the Boeing X-48 unmanned aerial vehicle.^[6] Studies suggested that a BWB airliner carrying from 450 to 800 passengers could achieve fuel savings of over 20 percent.^[5]: 21

Airbus is studying a BWB design as a possible replacement for the A320neo family. A sub-scale model flew for the first time in June 2019 as part of the MAVERIC (Model Aircraft for Validation and Experimentation of Robust Innovative Controls) programme, which Airbus hopes will help it reduce CO₂ emissions by up to 50% relative to 2005 levels.^[7]

The N3-X NASA concept uses a number of superconducting electric motors to drive the distributed fans to lower the fuel burn, emissions, and noise. The power to drive these electric fans is generated by two wingtip-mounted gas-turbine-driven superconducting electric generators. This idea for a possible future aircraft is called a "hybrid wing body" or sometimes a blended wing body. In this design, the wing blends seamlessly into the body of the aircraft, which makes it extremely aerodynamic and holds great promise for dramatic reductions in fuel consumption, noise and emissions. NASA develops concepts like these to test in computer simulations and as models in wind tunnels to prove whether the possible benefits would actually occur.^{[citation needed]}

In 2020, Airbus presented a BWB concept as part of its ZEROe initiative and demonstrated a small-scale aircraft.^[8][9] In 2022, Bombardier announced its EcoJet project.^{[9][10][better source needed]} In 2023, California startup JetZero announced its Z5 project, designed to carry 250 passengers, targeting the New Midmarket Airplane category, expecting to use existing CFM International LEAP or Pratt & Whitney PW1000G 35,000 lbf (160 kN) engines.^[11][12] In August 2023, the U.S. Air Force announced a $235-million contract awarded over a four-year period to JetZero, culminating in first flight of the full-scale demonstrator by the first quarter of 2027. The goal of the contract is to demonstrate the capabilities of BWB technology, giving the Department of Defense and commercial industry more options for their future air platforms.^[13][14]

Following this development, JetZero has received FAA clearance for test flights of its Pathfinder, a 'blended-wing' demonstrator plane designed to significantly reduce drag and fuel consumption. This innovative design could potentially lower emissions by 50%. Scheduled for full-scale development by 2030, JetZero plans to create variants for passengers, cargo, and military use. The project faces challenges in certification and integration with current airport infrastructures.^[15]

The wide interior spaces created by the blending pose novel structural challenges. NASA has been studying foam-clad stitched-fabric carbon fiber composite skinning to create uninterrupted cabin space.^[16]

The BWB form minimizes the total wetted area – the surface area of the aircraft skin, thus reducing skin drag to a minimum. It also creates a thickening of the wing root area, allowing a more efficient structure and reduced weight compared to a conventional craft. NASA also plans to integrate Ultra High Bypass (UHB) ratio jet engines with the hybrid wing body.^[17]

A conventional tubular fuselage carries 12–13% of the total lift compared to 31–43% carried by the centerbody in a BWB, where an intermediate lifting-fuselage configuration better suited to narrowbody-sized airliners would carry 25–32% for a 6.1–8.2% increase in fuel efficiency.^[18]

Spectrum of aircraft design concepts. From left to right: conventional airliner (Boeing 757), blended wing body (B-1 Lancer), flying wing with bulged fairings (B-2 Spirit), and almost clean flying wing (Northrop YB-49) and Lifting body (M2-F1).

• Significant payload advantages in strategic airlift, air freight,^[19] and aerial refueling roles
• Increased fuel efficiency — 10.9% better than a conventional widebody,^[18] to over 20% than a comparable conventional aircraft.^[20] A 2022 US Air Force report shows a BWB "increases aerodynamic efficiency by at least 30% over current air force tanker and mobility aircraft".^[21]
• Lower noise — NASA audio simulations show a 15 dB reduction of Boeing 777-class aircraft,^[22] while other studies show 22–42 dB reduction below Stage 4 level, depending on configuration.^[2]

• Evacuating a BWB in an emergency could be a challenge. Because of the aircraft's shape, the seating layout would be theater-style instead of tubular. This imposes inherent limits on the number of exit doors.^[23][24]
• It has been suggested that BWB interiors would be windowless;^[25] more recent information shows that windows may be positioned differently but involve the same weight penalties as a conventional aircraft.^[26]
• It has been suggested that passengers at the edges of the cabin may feel uncomfortable during wing roll;^[25] however, passengers in large conventional aircraft like the 777 are equally susceptible to such roll.^[26]
• The center wingbox needs to be tall to be used as a passenger cabin, requiring a larger wing span to balance out.^[27]
• A BWB has more empty weight for a given payload, and may not be economical for short missions of around four or fewer hours.^[27]
• A larger wing span may be incompatible with some airport infrastructure, requiring folding wings similar to the Boeing 777X.
• It is more expensive to modify the design to create differently-sized variants compared to a conventional fuselage and wing which can be stretched or shrunk easily.^[27]
• Pitch control and lift capability at low speed have presented challenges for blended-wing designs. JetZero has proposed a novel landing gear design to address these issues for its Z-5 BWB concept.^[11]

A concept photo of a blended wing body commercial aircraft appeared in the November 2003 issue of Popular Science magazine.^[30] Artists Neill Blomkamp and Simon van de Lagemaat from The Embassy Visual Effects created the photo for the magazine using computer graphics software to depict the future of aviation and air travel.^[31] In 2006 the image was used in an email hoax claiming that Boeing had developed a 1000-passenger jetliner (the "Boeing 797") with a "radical Blended Wing design" and Boeing refuted the claim.^[32][33][34]

• Aurora D8
• Flying-V jet
• List of flying wings
• Lifting body
• Silent Aircraft Initiative, a BWB study

• Al Bowers (Sep 16, 2000). "Blended-wing-body: Design challenges for the 21st century". The Wing is The Thing. Archived from the original on 2002-12-01.
• V. Mukhopadhyay (April 2005). Blended-Wing-Body (BWB) Fuselage Structural Design for Weight Reduction (PDF). 46th AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics and Materials Conference. NASA Technical Reports Server.
• "'Blended wing' craft passes wind-tunnel tests". New Scientist. 14 November 2005.
• "'Silent aircraft': How it works". BBC. 6 November 2006.
• R. Vos; F.J.J.M.M. Geuskens; M.F.M. Hoogreef (April 2012). "A New Structural Design Concept for Blended Wing Body Cabins". 53rd AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics and Materials Conference. Archived from the original on 2018-07-22.
• A Blended Wing Body Concept. AVD20112012. May 4, 2012. Archived from the original on 2021-12-21 – via YouTube.
• "X-48 Highlights". NASA. Apr 18, 2013. Archived from the original on July 8, 2017. Retrieved February 1, 2011.
• Jörg Fuchte; Till Pfeiffer; Pier Davide Ciampa; Björn Nagel; Volker Gollnick (September 2014). "Optimization of revenue space of a blended wing body" (PDF). 29th Congress of the International Council of the Aeronautical Sciences (ICAS 2014).