An open wagon (or truck in the UK) forms a large group of railway goods wagons designed primarily for the transportation of bulk goods that are not moisture-retentive and can usually be tipped, dumped or shovelled. The International Union of Railways (UIC) distinguishes between ordinary wagons (Class E/UIC-type 5) and special wagons (F/6).^[1][2] Open wagons often form a significant part of a railway company's goods wagon fleet; for example, forming just under 40% of the Deutsche Bahn's total goods wagon stock in Germany.

Since the 1960s, the majority of goods wagons procured by European railway administrations have been built to standards laid down by, or based on, those established by the UIC. In addition to open wagons the table also shows wagons with opening roofs (Class T), whose design is based on open wagons.

• Examples of standard open wagons
• 
  Twin-axled UIC Type 1 open wagon, used as an ash wagon, on a transporter wagon in Zittau
• 
  A Czech (ČD) twin-axled open wagon of UIC Type 2 in Raspenava

These wagons have a level floor and solid sides with at least one door on each side. They are mainly used for transporting bulk goods, coal, scrap, steel, wood and paper. The majority of wagons have folding sides and end walls, otherwise they are given the letters l (fixed sides) or o (fixed end walls). Wagons may have one or two folding end walls. Steel rings enable ropes, nets or covers to be attached to secure the load.

Some of these wagons can also be completely tipped over, in other words, at certain places they can be lifted up and emptied by being turned about their longitudinal axis. This requires a very robust underframe. Sometimes the wagons are fitted with rotatable couplings so that they do not have to be individually uncoupled.

In 1998, the Deutsche Bahn (DB) had about 16,000 four-axle Class E wagons. They have increasingly retired their twin-axled E wagons since the 1990s and they are now rarely seen.

The majority of these are self-discharging wagons which use gravity-unloading (hopper cars and saddle-bottomed wagons), but in addition there are also:

• Side-tipping wagons (box tip, trough-tip or side-tip wagon),
• Bucket wagon, other open wagons without side doors

In addition to hopper and saddle-bottomed wagons there were also wagons with opening roofs.^{[citation needed]}

Typical loads for these wagons are all sorts of bulk goods, like coal, coke, ore, sand or gravel. Because bulk goods are often moved in large quantities, these wagons are frequently used in so-called unit or block trains that only comprise one type of wagon and only shift one type of product from the dispatcher to the recipient.

Hopper wagons can only be unloaded by gravity with no external assistance and are therefore also classed as self-discharging wagons. The majority may be filled, when at rail or road level, by high-level discharge chutes (whose ends are more than 70 cm above the top of the rails) or conveyor belts. Because a controlled amount of the load can be discharged at any place the wagons may be sent anywhere and are even used individually. Railway companies also use hoppers as departmental wagons in maintenance of way trains for ballasting the track.

Since the 1990s there has been a trend for new hopper wagons to be built as bogie wagons which have not yet been standardized by the UIC.

• Examples of hopper wagons
• 
  Fccs hopper of the ITL railways
• 
  Funnel-shaped wagon floor
• 
  Controllable discharge equipment
• 
  Wheelset and brake rods
• 
  Axleboxes and double-shackle running gear
• 
  Swedish iron ore hopper (mineral wagon), built in 1900
• 
  Kambarka Engineering Works hopper car to transport track ballast, 750 mm (2 ft 5+1⁄2 in) gauge
• 
  Fcs⁰⁹²:Open wagon with controllable self-discharge equipment and high chute (hopper wagon)

Saddle-bottomed wagons are large-volume hoppers are exclusively unloaded by gravity and are therefore classed as self-discharging hoppers. Unlike normal hopper wagons, however, their discharge cannot be controlled and the entire load must be dropped. To unload the flaps on the side swing out allowing the load to empty. This is aided by the floor which slopes downwards on both sides like a gable roof. The discharging chutes on either side are relatively high up. These wagons are frequently seen in unit trains for transporting bulk goods such as coal or mineral ore from mines or ports to steelworks or power stations.

The most modern type of four axle saddle-bottomed wagon in the DB is the four axle Falns 121 with a loading volume of 90 m³ (120 cu yd). It was built from 1992 in several batches. By February 2008 another 100 of these wagons were to have been delivered to the DB and another 300 by 2010. These latest wagons will have an axle load of 23.5 t (23.1 long tons; 25.9 short tons) and an unladen weight of no more than 24.5 t (24.1 long tons; 27.0 short tons), resulting in a load limit of 69.5 t (68.4 long tons; 76.6 short tons).

Side-tipping wagons have hydraulic, pneumatic or electric tipping equipment, that enables the wagon body to be lifted on one side. Depending on the design, they may be tipped to both sides or just one side only. In order to prevent wagons from falling over during the tipping operation, some are equipped with track pinch bars with which they can be securely anchored to the trackbed. These wagons are often seen in unit trains being used to remove excavated material from major construction sites.

• Example of side-tipping wagons
• 
  A Czech (ČD) side tipper
• 
  The ČD groups these wagons into Class Ua
• 
  The tipping system can be seen from the end
• 
  US-style bogie on a side-tipping wagon
• 
  Coupling and main air pipe on a side-tipping wagon

A lorry or mine car is an open railroad car (gondola) with a tipping trough, used in mining. It is known in the UK as a tippler or chaldron wagon,^[3] and in the US as a mine car.^[4]

The first railway bulk-cargo gondolas, the first freight wagons, were the chaldron cars of the early coal-carrying plateways. These were relatively short in length and tall in proportion, with a tapered body that widened upwards, above the wheels. Once locomotive haulage began, the unstable and top-heavy nature of this design became a problem with increasing speeds and later wagons became lower and longer. The chaldron shape survived in a few cases, such as low-speed working around a large factory sites including steelworks.

Modalohrs are specialized wagons for carrying road trailers and road tractors on the AFF route from France to Italy and Luxembourg to Spain and vice versa; there are plans to expand this service.^[5] A deck between the bogies (trucks) pivots (swings) 30°, allowing the trailers to be loaded from the sides. The cars are built by Lohr Industrie.

• Examples of intermodal open wagons
• 
  A Tiphook rail intermodal freight well car at Banbury station in the UK in 2001
• 
  A pocket wagon
• 
  Special wagon of Hupac for semi-trailers
• 
  Semi-trailer on a Kangourou wagon^[6]

• Austauschbauart – German railway vehicles
• Class U special wagon – railway goods wagonsPages displaying wikidata descriptions as a fallback
• German state railway norms – Standards for railway vehicles in Germany
• Holocaust trains § The journey and point of arrival – Use as prisoner transport in the Holocaust
• Kriegsbauart – Railway goods wagons developed in WWII
• Lowmac – Specialty rail wagon for transporting vehicles
• Quarry tub – Railway wagon used at quarries and mines
• Slate waggon – Specialized types of railway wagons
• Verbandsbauart – Goods wagon

• Class Ua side-tippers in the Czech archives at parostroj.net
• DB goods wagon catalogue
• Flexiwaggon