Cent

United States
Value	$0.01 U.S. dollars
Mass	2.702 g
Diameter	19.05 mm
Thickness	1.55 mm
Edge	Plain
Composition	99% steel with a thin layer of zinc
Years of minting	1943
Catalog number	-
Obverse
Design	Abraham Lincoln
Designer	Victor D. Brenner
Design date	1909
Reverse
Design	Wheat Heads in memoria
Designer	Victor D. Brenner
Design date	1909

1943 steel cents are U.S. one-cent coins that were struck in steel due to wartime shortages of copper. The Philadelphia, Denver, and San Francisco mints each produced these 1943 Lincoln cents. The unique composition of the coin (low-grade steel coated with zinc, instead of the previously 95%-copper-based bronze composition) has led to various nicknames, such as wartime cent, steel war penny, zinc cent and steelie. The 1943 steel cent features the same Victor David Brenner design for the Lincoln cent which had been in use since 1909.

Due to wartime needs of copper for use in ammunition and other military equipment during World War II, the United States Mint researched various ways to limit dependence and meet conservation goals on copper usage. After trying out several substitutes (ranging from other metals^[1] to plastics^[2]) to replace the then-standard bronze alloy, the one-cent coin was minted in zinc-coated steel. This alloy caused the new coins to be magnetic and 13% lighter. They were struck at all three mints: Philadelphia, Denver, and San Francisco. As with the bronze cents, coins from the latter two sites have respectively "D" and "S" mintmarks below the date.

However, problems began to arise from the mintage. Freshly minted, they were often mistaken for dimes. Magnets in vending machines (which took copper cents) placed to pick up steel slugs also picked up the legitimate steel cents. Because the galvanization process did not cover the edges of the coins,^[why?] sweat would quickly rust the metal. After public outcry, the Mint developed a process whereby salvaged brass shell casings were augmented with pure copper to produce an alloy close to the 1941–42 composition. This was used for 1944–46-dated cents, after which the prewar composition was resumed. Although they continued to circulate into the 1960s, the mint collected large numbers of the 1943 cents and destroyed them.^[3]

The steel cent is the only regular-issue United States coin that can be picked up with a magnet. The steel cent was also the only coin issued by the United States for circulation that does not contain any copper.^[4] (Even U.S. gold coins at various times contained from slightly over 2% copper to an eventual standard 10% copper to increase resistance to wear by making the pure gold coins slightly harder).

Far ahead of the 1955 doubled die cent in rarity, the 1943 copper cent is one of the notable rarities of the Lincoln cent series. An estimated 40 examples are believed to have been struck, with 13 confirmed to exist. The error occurred when copper planchets were left in the press hopper and press machines during the changeover from copper to steel blanks. Examples were discovered after the War, with the first two in 1947,^[5] and another in 1958. That example appeared in a 1958 Abe Kosoff sale, but was withdrawn prior to the sale; one mint condition Denver Mint specimen sold for over $1.7 million in 2010.^[6]

Many people have counterfeited the coin by either copper-plating normal 1943 cents (sometimes as novelties with no intent to defraud), or altering cents from the period, usually 1945, 1948, or 1949-dated coins.

The copper cents differ from their steel counterparts in four ways:^[7]

• Genuine 1943 copper cents will not be attracted to a magnet. Copper-plated steel cents will exhibit a strong magnetic attraction.
• Copper cents weigh 3.11 grams. Steel cents weigh 2.702 grams.
• The numeral 3 in 1943 has the same long tail as the steel cents. Alterations from later-dated copper cents will be noticeable when compared side by side with genuine cents with years ending in 3.
• The quality of the strike is exceptionally sharp, especially around the rim, because the soft copper planchets were struck with the same (higher) pressure used for the steel cents.

In 2019, NGC authenticated a worn 1943 cent composed of 86.41% tin and 8.37% antimony with other trace metals. The coin was discovered by a coin collector in the state of Oregon, who found it in his father's yard c. 1969 and realized it was not attracted to a magnet while searching his coin collection for 1943 copper cents in 2019. It is likely that the coin is an error or was intentionally struck as a pattern in late 1942 using an obverse die intended for the following year, though no documented evidence of a pattern with this composition has been found.^[8]

The coin was found in a badly damaged state, with two large gashes and a slight bend. Believing it to be a steel cent, the discoverer straightened the coin in a bench vise so that it would fit inside a coin album. The coin weighs 2.702 g.^[8]

In an error similar to the 1943 cents, a few 1944 cents were struck on steel planchets left over from 1943.^[7] There are two explanations given for why this happened. One explanation is that steel planchets were left in the press hopper and press machines from the previous year mixed in with copper planchets.^[5][7] Another explanation credits the error to the production of 25 million^[5][9] Belgian two franc pieces by the Philadelphia mint after that country's liberation from the Nazis.^[5][7] These coins were of the same composition^[7] and the same planchets^[5][9] as the 1943 cents, but they differed slightly in weight.^[7] In all, 1944 steel cents are fewer in number than their 1943 copper counterparts,^[7] and are even more valuable; one such example minted in San Francisco sold for $373,750 in an August 2008 auction held by Heritage Auctions; this was the highest auction price ever for a Lincoln cent until September 23, 2010, when it was superseded by a 1943-D bronze penny.^[10][11][6]

Although United States penny is widely known to hold a higher mintage cost than its face value, the United States actually made a large profit on minting steel coins. In 1943, the cost of a gross ton of steel was $34.^[12]

Since many steel cents corroded and became dull soon after entering circulation, some dealers who sold the coins as novelties improved their appearance by "reprocessing" – stripping off the old zinc coating and then replating them with zinc or chrome. These reprocessed coins are sometimes erroneously described as brilliant uncirculated, or similar terms, by ignorant or unscrupulous online sellers.^{[13][14][15][16]}

• 2 francs (World War II Belgian coin)
• 'War Nickels', 1942–1945 Jefferson nickels produced with 35% silver instead of nickel, due to nickel requirements by the U.S. military
• Sales tax token