Early effect

The Early effect, named after its discoverer James M. Early, is the variation in the effective width of the base in a bipolar junction transistor (BJT) due to a variation in the applied base-to-collector voltage. A greater reverse bias across the collector–base junction, for example, increases the collector–base depletion width, thereby decreasing the width of the charge carrier portion of the base.

Explanation

In Figure 1, the neutral (i.e. active) base is green, and the depleted base regions are hashed light green. The neutral emitter and collector regions are dark blue and the depleted regions hashed light blue. Under increased collector–base reverse bias, the lower panel of Figure 1 shows a widening of the depletion region in the base and the associated narrowing of the neutral base region.

The collector depletion region also increases under reverse bias, more than does that of the base, because the collector is less heavily doped than the base. The principle governing these two widths is charge neutrality. The narrowing of the collector does not have a significant effect as the collector is much longer than the base. The emitter–base junction is unchanged because the emitter–base voltage is the same.

Base-narrowing has two consequences that affect the current:

There is a lesser chance for recombination within the "smaller" base region.
The charge gradient is increased across the base, and consequently, the current of minority carriers injected across the collector-base junction increases, which net current is called $I_{\text{CB0}}$ .

Both these factors increase the collector or "output" current of the transistor with an increase in the collector voltage, but only the second is called Early effect. This increased current is shown in Figure 2. Tangents to the characteristics at large voltages extrapolate backward to intercept the voltage axis at a voltage called the Early voltage, often denoted by the symbol V_A.

Large-signal model

In the forward active region the Early effect modifies the collector current ( $I_{\mathrm {C} }$ ) and the forward common-emitter current gain ( $\beta _{\mathrm {F} }$ ), as typically described by the following equations:^[1]^[2]

{\begin{aligned}I_{\mathrm {C} }&=I_{\mathrm {S} }e^{\frac {V_{\mathrm {BE} }}{V_{\mathrm {T} }}}\left(1+{\frac {V_{\mathrm {CE} }}{V_{\mathrm {A} }}}\right)\\\beta _{\mathrm {F} }&=\beta _{\mathrm {F0} }\left(1+{\frac {V_{\mathrm {CE} }}{V_{\mathrm {A} }}}\right)\end{aligned}}

where

$V_{\mathrm {CE} }$ is the collector–emitter voltage
$V_{\mathrm {BE} }$ is the base–emitter voltage
$I_{\mathrm {S} }$ is the reverse saturation current
$V_{\mathrm {T} }$ is the thermal voltage $\mathrm {kT/q}$ ; see thermal voltage: role in semiconductor physics
$V_{\mathrm {A} }$ is the Early voltage (typically 15–150 V; less for smaller devices)
$\beta _{\mathrm {F0} }$ is forward common-emitter current gain at zero bias.

Some models base the collector current correction factor on the collector–base voltage V_CB (as described in base-width modulation) instead of the collector–emitter voltage V_CE.^[3] Using V_CB may be more physically plausible, in agreement with the physical origin of the effect, which is a widening of the collector–base depletion layer that depends on V_CB. Computer models such as those used in SPICE use the collector–base voltage V_CB.^[4]

Small-signal model

The Early effect can be accounted for in small-signal circuit models (such as the hybrid-pi model) as a resistor defined as^[5]

r_{\text{O}}={\frac {V_{\text{A}}+V_{\text{CE}}}{I_{\text{C}}}}\approx {\frac {V_{\text{A}}}{I_{\text{C}}}}

in parallel with the collector–emitter junction of the transistor. This resistor can thus account for the finite output resistance of a simple current mirror or an actively loaded common-emitter amplifier.

In keeping with the model used in SPICE and as discussed above using $V_{CB}$ the resistance becomes:

r_{\text{O}}={\frac {V_{\text{A}}+V_{\text{CB}}}{I_{\text{C}}}}

which almost agrees with the textbook result. In either formulation, $r_{O}$ varies with DC reverse bias $V_{CB}$ , as is observed in practice.^{[citation needed]}

In the MOSFET the output resistance is given in Shichman–Hodges model^[6] (accurate for very old technology) as:

r_{\text{O}}={\frac {1+\lambda V_{\text{DS}}}{\lambda I_{\text{D}}}}={\frac {1}{I_{\text{D}}}}\left({\frac {1}{\lambda }}+V_{\text{DS}}\right)

where $V_{\text{DS}}$ = drain-to-source voltage, $I_{\text{D}}$ = drain current and $\lambda$ = channel-length modulation parameter, usually taken as inversely proportional to channel length L. Because of the resemblance to the bipolar result, the terminology "Early effect" often is applied to the MOSFET as well.

Current–voltage characteristics

The expressions are derived for a PNP transistor. For an NPN transistor, n has to be replaced by p, and p has to be replaced by n in all expressions below. The following assumptions are involved when deriving ideal current-voltage characteristics of the BJT^[7]

Low level injection
Uniform doping in each region with abrupt junctions
One-dimensional current
Negligible recombination-generation in space charge regions
Negligible electric fields outside of space charge regions.

It is important to characterize the minority diffusion currents induced by injection of carriers.

With regard to pn-junction diode, a key relation is the diffusion equation.

{\frac {d^{2}\Delta p_{\text{B}}(x)}{dx^{2}}}={\frac {\Delta p_{\text{B}}(x)}{L_{\text{B}}^{2}}}

A solution of this equation is below, and two boundary conditions are used to solve and find $C_{1}$ and $C_{2}$ .

\Delta p_{\text{B}}(x)=C_{1}e^{\frac {x}{L_{\text{B}}}}+C_{2}e^{-{\frac {x}{L_{\text{B}}}}}

The following equations apply to the emitter and collector region, respectively, and the origins $0$ , $0'$ , and $0''$ apply to the base, collector, and emitter.

{\begin{aligned}\Delta n_{\text{B}}(x'')&=A_{1}e^{\frac {x''}{L_{\text{B}}}}+A_{2}e^{-{\frac {x''}{L_{\text{B}}}}}\\\Delta n_{\text{c}}(x')&=B_{1}e^{\frac {x'}{L_{\text{B}}}}+B_{2}e^{-{\frac {x'}{L_{\text{B}}}}}\end{aligned}}

A boundary condition of the emitter is below:

\Delta n_{\text{E}}(0'')=n_{{\text{E}}O}\left(e^{{\frac {1}{kT}}qV_{\text{EB}}}-1\right)

The values of the constants $A_{1}$ and $B_{1}$ are zero due to the following conditions of the emitter and collector regions as $x''\rightarrow 0$ and $x'\rightarrow 0$ .

{\begin{aligned}\Delta n_{\text{E}}(x'')&\rightarrow 0\\\Delta n_{\text{c}}(x')&\rightarrow 0\end{aligned}}

Because $A_{1}=B_{1}=0$ , the values of $\Delta n_{\text{E}}(0'')$ and $\Delta n_{\text{c}}(0')$ are $A_{2}$ and $B_{2}$ , respectively.

{\begin{aligned}\Delta n_{\text{E}}(x'')&=n_{{\text{E}}0}\left(e^{\frac {qV_{\text{EB}}}{kT}}-1\right)e^{-{\frac {x''}{L_{\text{E}}}}}\\\Delta n_{\text{C}}(x')&=n_{{\text{C}}0}\left(e^{\frac {qV_{\text{CB}}}{kT}}-1\right)e^{-{\frac {x'}{L_{\text{C}}}}}\end{aligned}}

Expressions of $I_{{\text{E}}n}$ and $I_{{\text{C}}n}$ can be evaluated.

{\begin{aligned}I_{{\text{E}}n}&=\left.-qAD_{\text{E}}{\frac {d\Delta _{\text{E}}(x'')}{dx}}\right|_{x''=0''}\\I_{{\text{C}}n}&=-qA{\frac {D_{\text{C}}}{L_{\text{C}}}}n_{{\text{C}}0}\left(e^{\frac {qV_{\text{CB}}}{kT}}-1\right)\end{aligned}}

Because insignificant recombination occurs, the second derivative of $\Delta p_{\text{B}}(x)$ is zero. There is therefore a linear relationship between excess hole density and $x$ .

\Delta p_{\text{B}}(x)=D_{1}x+D_{2}

The following are boundary conditions of $\Delta p_{\text{B}}$ .

{\begin{aligned}\Delta p_{\text{B}}(0)&=D_{2}\\\Delta p_{\text{B}}(W)&=D_{1}W+\Delta p_{\text{B}}(0)\end{aligned}}

with W the base width. Substitute into the above linear relation.

\Delta p_{\text{B}}(x)=-{\frac {1}{W}}\left[\Delta p_{\text{B}}(0)-\Delta p_{\text{B}}(W)\right]x+\Delta p_{\text{B}}(0)

With this result, derive value of $I_{{\text{E}}p}$ .

{\begin{aligned}I_{{\text{E}}p}(0)&=\left.-qAD_{\text{B}}{\frac {d\Delta p_{\text{B}}}{dx}}\right|_{x=0}\\I_{{\text{E}}p}(0)&={\frac {qAD_{\text{B}}}{W}}\left[\Delta p_{\text{B}}(0)-\Delta p_{\text{B}}(W)\right]\end{aligned}}

Use the expressions of $I_{{\text{E}}p}$ , $I_{{\text{E}}n}$ , $\Delta p_{\text{B}}(0)$ , and $\Delta p_{\text{B}}(W)$ to develop an expression of the emitter current.